## SuperFOIL – Croft School 1600 sq. m SF40 Install

http://www.superfoil.co.uk/news/croft-school-sf40-install/

A video demonstrating SF40 being used on a school refurbishment project.

Taking a school from poor insulation ratings to better than current regulations, providing the students and teachers with a high level of comfort and warmth.

Chosen for its ease of installation and cost efficiency, no other brands’ multi-foil has the performance of SuperFOIL SF40!

## SuperFOIL – HOW TO Retrofit Multi Layer Foil Roof Insulation

http://www.superfoil.co.uk/news/superfoil-how-to-retrofit-multi-layer-foil-roof-insulation/

A short video showing just how easy it is to retrofit your house with SuperFOIL!

Armed with some scissors, a stapler and a roll of foil tape you see the workers re-fitting an attic with SuperFOIL insulation.

You can request a free sample pack and the SuperFOIL team are always happy to provide any needed information.

## The Value Of Air In Insulation

http://www.superfoil.co.uk/news/the-value-of-air-in-insulation/

Air is a very good insulator, for instance the thermal conductivity of air is 0.24, which is much better than old fashioned glass fibre at 0.44 (the lower figure the better). Above and beyond that a sealed air gap next to a reflective surface improves the R value of the air, there is a useful EN standard called EN6946 that you can use to calculate the R value of an air gap if you have the emissivity (reflectiveness) of the foil.

A sealed air gap will be up to 200% improved if the emissivity of the foil is good. Air is a good insulator but its important that the air is kept still; convection currents in air reduce performance. This is why glass wool was used an an insulator for a long time, it works to keep air from moving around. If you compare the thermal conductivity of glass to glass fibre it is very poor (think how cold single glazing is); the same glass made into glass wool is a lot better because although its an open structure it’s trying to keep the air still. Foam board is the same, doing what glass wool does but more efficiently.

Multi layer foil insulation takes the technology further, combining sealed air gaps with reflective surfaces to not only create efficient air gaps but to create super efficient low emissivity air gaps. Each layer in Superfoil multi foil insulation creates an improved performance air gap and beyond that creates improvements between its self and the plaster board below and the secondary rain barrier membrane above.

In a roof EN6946 states that the efficiency starts to reduce in air gaps below 13mm, in walls its 20mm. Battens are incorporated in the construction detail of Superfoil multifoil to ensure the minimum air gap is maintained. A multilayer foil can reduce a timber frame wall from 300mm, sized to accommodate the amount of glass wool needed, to that needed purely for structural strength, which may be only 100mm. A significant saving on timber and labour is achieved.

Air is a good insulator and Superfoil multifoil insulation takes the greatest advantage of that. Air is also probably the cheapest form of insulation available! Superfoil multilayer foil insulations maximize the contribution of air, by applying science and technology to create a leading edge insulation.

## SF40 Performance Options

http://www.superfoil.co.uk/news/sf40-performance-options/

SF40 our double thickness foil insulation is a favorite with professional loft converters and self builders alike, SF40 is combined with with 40mm foam backed plasterboard to give a U 0.18 is an LABC approved registered detail and meets current building regs the finished ceiling will be 90mm ( 3 1/2 inches) below the rafter

No insulation is required between rafters at all, great for time and cost saving and where rafters are small and the often essential ventilation gap is not lost.

SF40 can be used in a variety of ways, for those insulating under rafters using two layers of SF40 provides easy install and excellent results.

A standard SF40 2 layer ”Duet” detail is ;- Rafter, SF40, Batten, SF40, Batten, Plasterboard, this gives a U value of 0.147 , the finished ceiling will be 143mm mm ( 5 5/8th inches) below the rafter (see below picture figure B).

A couple of other details brought to our attention by experienced installers giving home owners higher specifications are U 0.135 this requires adding a layer of SFTV and another batten in the middle, the finished ceiling will be 156mm mm ( 6 3/8th inches) below the rafter (see below picture figure A). Or for space saving without the central middle low emissivity air gap its U 0.157 the finished ceiling will be 130mm mm ( 5 1/8th inches) below the rafter (see below picture figure C).

All 3 options give ease of install, add to air tightness, provide a radiant barrier which reduce solar gain in summer with improved thermal performance significantly better than current regs.

To request U value calculations and install details use the contact button.

## New 2010 Insualtion Regulations – SuperFOIL Foil Insulation

October 2010 Building Regulations Part L for Insulation –

http://www.superfoil.co.uk/news/new-2010-insualtion-regulations/

The regulations have increased building insulation requirements as high as U 0.16 .
SuperFOIL have already had solutions for U values down to as low as U 0.11. We have a wide range of solutions to satisfy the existing regulations and have developed new solutions for the new standards.

The target levels for different elements within a building can be seen below.

 Element Old New Sloping Roof 0.20 0.18 External Wall 0.30 0.28 Floor 0.25 0.22 Ceiling Level 0.16 0.16 Flat Roof 0.20 0.18

To meet these regulations we have listed a range of solutions and u-value calculations which either meet or exceed the new regulations (subject to the elements of the building structure you are trying to insulate).

Follow the links below to take you to a surveyor certified U value calculation that you can print for your building inspector.

Ceiling Level Insulation– 2010 U-value required U 0.16

DUET Solution (Superfoil only)
U 0.13 Use SF40 + SF40 Over or under rafters (Better than new Regs)

COMBI Solutions (using Superfoil and other insulation together)
U 0.16 Use SF19 + 150mm Glassfibre between rafters

Sloping Roof / Flat Roof – 2010 U-value required U 0.18

DUET Solutions (Superfoil only)
U 0.18 Use SF40 + SF19 over or under rafters
or
U 0.13 Use SF40 + SF40 Over or under rafters (Better than the new Regs)

COMBI Solutions (using Superfoil and other insulation together)

U 0.18 use SF40 + 35mm Insulated Plasterboard below rafters

Floor – 2010 U-value required U 0.22
U 0.22 use SFUF + 50mm HD Foam Board

External Wall – 2010 U-value required U 0.28
U 0.25 Use SF40 in a solid & Stud wall (Better than the new Regs)
Or
U 0.24 Use SF40 stone wall (better than the new Regs)

Or
U 0.13 SF40 + SF40 in a timber wall (Better than the new Regs)

## SuperFoil SF19 and SuperFoil SF40 gain LABC Registered Detail approval

http://www.superfoil.co.uk/news/superfoil-sf19-and-superfoil-sf40-gain-labc-registered-detail-approval/

Boulder Developments Ltd is delighted to announce that both SF19 SuperFoil and SF40 SuperFoil insulation products are now approved under the LABC Registered Detail scheme for use in roofs and walls.

The Registered Detail approval enables Local Authority Building Control Officers to move forward speedily with the approval of the insulation requirements for your new build, extension or renovation project and provides LABC’ s customers with confidence in their choice of SuperFoil. Furthermore, it also brings the opportunity to save time which in turn leads to saving money.

The rigorous assessment by the LABC approval team means that all aspects of the products performance has been assessed and confirmed. The process also involves the assessment of practical applications and installation guidance to ensure that the current 2010 Building Regulation standards are in all cases achieved and in some exceeded!

The SuperFoil range of products is unique and provides the end user with a choice of the most effective multi layered foil for their specific use. The variation in rafter depth, the location of the insulation at rafter or ceiling level, an internal or external application can all be accommodated; each SuperFoil product is distinguished by thermal performance rating making it is easy to choose the most effective product for your project.

Installing Superfoil is easy and results in minimal waste; SuperFoil is manufactured with 40% recycled materials and is recyclable at the end of its useful life. SF products are non -hazardous and there are no special requirements for installation or disposal of waste.